(Note: all images are courtesy of the Jurriaan Schrofer archive in the special collections of the Allard Pierson Museum, University of Amsterdam, unless credited otherwise.)
Photo: Tjeerd Frederikse. Reproduced in Huygen, Total Design 1982–1996: een ontwerpbureau in transitie (2001). The photo is in the TD archives, now kept in the Staadsarchief Amsterdam.
Yes, this really is the shape of the book.
Photo:
Johan van Gurp. Reproduced in Huygen (2001).
Photo: Rietveld Stichting (gerrit-rietveld.nl)
Photo: Rietveld Stichting (gerrit-rietveld.nl)
Photo: 20th Century Architecture (architecture-history.org)
Photo: Jan Versnel, via ZEEP Architects (zeep.eu)
Photo: De Stad Amersfoort (destadamersfoort.nl)
Photo: Amersfoort Nieuws (amersfoort.nieuws.nl)
While most of the boards have captions, they are unnumbered and weren’t stored in any recognizable order. I first tried to reconstruct the display and the order of the boards based on the materials on them and on what was visible of the books and panels in the photographs. But in a subsequent visit to Schrofer’s archive in October 2023, an archivist I had been working with closely brought me a box of materials from the archive of another TD senior designer, Jolijn van de Wouw.
The note reads: ‘Passport design by J. Schrofer (TD) / Unclear whether J vd Wouw helped out’. It’s pretty clear to me that she did.
Note the dates: TD received Schrofer’s manuscript 23 August, and the clean copy was ready 25 August 1983—well after the close of the exhibit at De Beyerd.
Again, visitors to the exhibit who encountered Schrofer’s display would have seen two sets of three large wall-mounted panels, and two sets of smaller boards bound into books resting on pedestals. The wall panels, which aren’t preserved in Schrofer’s archive, were attached at their tops to what looks like a strip of wood mounted on the brick wall. They were probably A0 format (84.1 × 118.9cm / 33.1 × 46.8in) and they didn’t appear to have labels. The materials on the panels are preserved in the archives.
There are 45 smaller boards, 21 for the part I book and 24 for part II, in B2 format (50 × 70.7cm / 19.7 × 27.8in). Here they are in order, with translations of the captions [and my notes and questions where relevant]. (Keep in mind that the captions were intended for a general audience, not professional designers.)
Part I
1–2
[This introduction was prepared separately from the other captions, its location indicated in the typescript and fine copy by the text dialoog Schrofer/Oltheten.]
Foreword ¶These designs for a new passport, commissioned by the State Printing Office and the Ministry of Foreign Affairs, date from 1967–1972 [sic] and were made by Jurriaan Schrofer, who was associated with Total Design in the years 1974–1979. ¶Given the nature of the assignment—with all its substantive, technical, and design-related aspects—we felt that this account of a design process could serve as an example, offering insight into the approach and execution of such a project. ¶We are especially grateful to Mr. Th. H. Oltheten, until recently chief director of the State Printing and Publishing Offices—and, as such, often our client, too—for his work to make showing this record possible. ¶Directors, Total Design
Jurriaan Schrofer ¶Design for a passport ¶part I ¶1967–1968
[The dialoog was originally to appear separately on p 2, but apparently whoever assembled the display chose to combine pp 1–2. Page references here and in the captions reflect the original plan.]
1–2
[This introduction was prepared separately from the other captions, its location indicated in the typescript and fine copy by the text dialoog Schrofer/Oltheten.]
Foreword ¶These designs for a new passport, commissioned by the State Printing Office and the Ministry of Foreign Affairs, date from 1967–1972 [sic] and were made by Jurriaan Schrofer, who was associated with Total Design in the years 1974–1979. ¶Given the nature of the assignment—with all its substantive, technical, and design-related aspects—we felt that this account of a design process could serve as an example, offering insight into the approach and execution of such a project. ¶We are especially grateful to Mr. Th. H. Oltheten, until recently chief director of the State Printing and Publishing Offices—and, as such, often our client, too—for his work to make showing this record possible. ¶Directors, Total Design
Jurriaan Schrofer ¶Design for a passport ¶part I ¶1967–1968
[The dialoog was originally to appear separately on p 2, but apparently whoever assembled the display chose to combine pp 1–2. Page references here and in the captions reflect the original plan.]
In 1967 Jurriaan Schrofer was commissioned by the State Printing Office to investigate the possibilities for a new passport model. An important starting point was to find other graphic means for the traditional ‘guilloches’, the complicated geometric decorations that serve to protect against counterfeiting. ¶At the time Schrofer himself was experimenting as a designer with geometric structures that included variations of color, size, and orientation. ¶Top left: the general specifications the Dutch passport had to meet. ¶Top right: comparing the passports of 15 countries showed that there was hardly any similarity among them in layout and design.[*] ¶Bottom: more than anything else, confidentiality was required for designing a passport![†]
[*The memo lists the countries whose passports the Dutch Ministry of Foreign Affairs collected to share with Schrofer as examples.]
[†The State Printing Office memos acknowledging receipt of materials are all marked ‘secret’/‘confidential’.]
The explanation that Jurriaan Schrofer gave for his first design (at right), in which he described the motivation behind his starting points as well as for the chosen design.
[Based on the distribution of the six pages of Schrofer’s mimeographed typescript on the boards, pp 4–5 must have been visible as a spread.]
The paper had to be composed of such material to prevent alteration or forgery. ¶At the time, [the Dutch designer] Gerard Wernars had designed a new stylized national coat of arms for the State Printing Office. For Schrofer, it was an obvious choice to use his colleague’s contemporary design in the passport, in a few ways:
- printed on the cover and title page
- as a watermark on pages 3 and 4
- as a small watermark of one of the lions on every page
Top: the format of the [then-] existing passport, ‘model 1950’; the proposed format for the new passport, with sides in the ratio of 2:3; the format of the smallest [sample] passport, that of Czechoslovakia. ¶Middle: An initial overall layout plan for two facing pages showing the placement of the lion watermark. ¶Bottom: a layout plan showing the placement of the perforated numbers and page numbers in the passport’s interior.
[This is a sample of the linen for the cover described in the caption for p 9.]
The designer preferred a linen cover; see his explanation[*]. Instead of the traditional text ‘Kingdom of the Netherlands’, color would symbolize our country: green, red-white-blue. ¶The Van Heek [textile manufacturing] firm made a test fabric with different variations of red, white and blue (page 8). The left half is undyed, the right half is dyed, with the colored threads of Terlenka yarn not picking up the dye.
[*On p 5 above, on p 3 of 6 in Schrofer’s text explaining his proposal, under d. omslag (‘cover’), he explains: ‘You can choose between a hard or a flexible cover, and between a synthetic material or a natural fabric—specifically, linen. … The preference is for a flexible cover and for linen, as it feels more understated, authentic, and elegant.’]
The passport was to include perforated numbers [as a security feature]. On page 11 is a first attempt to design a bespoke perforation alphabet based on a hexagonal grid. The ‘perforation’ principle would be the starting point for further development in the second passport.
[There may be materials missing from this board. Schrofer likely would have had many other ‘attempts’ saved in his papers to share, as the other boards in these books—not to mention the 250+ boxes of materials in his archive—suggest.]
Instead of the guilloche decoration [in the existing passport], Schrofer wanted to print the background with a structure of colored letters. In these sketches, he investigated the possibility of using the 9 letters of the word ‘NEDERLAND’ to build structures in which changing the orientation of the letters would generate different variations. One particular problem he faced was designing a regular wave movement of the letters.
[Schrofer is describing the security pattern for the passport pages.]
Concept sketches for constructing the page background. The background would consist of a stack of three different letter structures to symbolize the concepts ’air-water-land’.
[This page is missing its caption: Een eerste, nog grofmazig stramien om de letter-strukturen op te schetsen. —An initial, rough framework for sketching the letter-structures.]
A color sketch, accompanied by a scaled-down version to allow for an assessment of the effect at actual size. Compare this with the first panel on the wall.
[Schrofer here and subsequently refers to the large panels over the relevant books.]
The definitive fine-meshed grid.
Blocks of text in rub-down letters (see the second panel on the wall) are photographically reduced and copied multiple times. In this way, larger fields can be assembled.
[The typeface for the dry-transfer letters is Aldo Novarese and Alessandro Butti’s Eurostile (a spiritual successor to/upgrade of their earlier Microgramma), released in 1962 by the Italian type foundry Nebiolo.]
The three zones are mounted one directly below the other, so that they naturally flow into one another.
[This page is missing its captions. The first: De kleuraanwijzing voor de drukkerij—hoort bij de komplete montage van de letters, die op paneel 3 te zien is.—The color specification for the printer—part of the complete assembly of the letters, which can be seen on panel 3.]
[The second caption I found floating separately in the archive box with the display boards and materials: Veel van wat we hier hebben gezien was handwerk; het zou tegenwoordig veel sneller door een computer-gestuurde fotozetmachine kunnen worden gedaan.—Much of what we have seen here was made by hand; today it could be done much faster by a computer-controlled phototypesetting machine.]
In 1968, the State Printing Office produced a number of trial pages using two colors: red+blue, blue+yellow, and red+yellow. The two printing plates were also swapped, resulting in six possible variations. The yellow+blue combination was chosen for the final proposal; see the example on page 5.
1
Jurriaan Schrofer ¶Design for a passport ¶part II/1972–1973 ¶In 1972 the Ministry of Foreign Affairs wanted to resume the development of a new passport. But there were some comments about the first draft, such as:
- the background was considered too ‘busy’, too ‘messy’
- The green linen met with resistance; it was felt that dark blue would be more appropriate, so as not to make the difference from the old passport too pronounced
The Ministry agreed that Schrofer would create a new design and would have a great deal of freedom in doing so. ¶Jurriaan Schrofer: ‘My response to all of this was that I did not want to make changes to the initial design, but rather start over from scratch—all the more so because I was already occupied with other projects. It seemed ideal to me to arrive at a form in which all elements—such as the perforations, typeface, background, and watermark—were harmonized. I also envisioned a design for the background printing on the pages that would create a gradual visual transition throughout the entire passport. This stood in contrast to the first design, in which the background print on every page was identical to that of the preceding and following pages. The Ministry of Foreign Affairs, the Government Printing Office, and I reached an agreement that I would start over …’
The concept of a ‘perforation alphabet’ from the initial design served as the starting point for a series of new typeface designs. A ‘grid’—a fixed arrangement of points in terms of height and width—was chosen as the foundation. In principle: the greater the number of points, the more refined the form of the letter can be. ¶Here we see an 8×8-point grid, with 4 points left unused (see top left)—leaving 60 points available. ¶Schrofer: ‘When choosing between a capital and a lowercase (small-letter) form for a given letterform, I prefer the lowercase. A second preference regarding the form of the letter is: better to use a diagonal running from the bottom-left to the top-right (/) than one from the top-left to the bottom-right (\). ¶A third objective was to keep the number of points used for each letter as consistent as possible, with a view to the overall typographic color [literally, the ‘grey value’] of the text. ¶My fourth objective was to avoid ‘islands’ within the letterforms (for example, in the o, the p, the a, etc.).’
[pp 4–5 are missing a caption: Een aantal probeersels op een stramien van 6×7 punten. —A number of attempts on a grid of 6×7 points.]
The system Schrofer finally chose: a grid of 5×5 points, of which 4 are not used.
A few working sketches, created using masking film, a material typically used in screenprinting. These served as the basis for the reduced-scale versions on page 9 (at the bottom, marked with a ‘+’).
[The ‘+’ reference isn’t clear in the materials. Four cells in the left array at the bottom of p 9 have ‘x’s in them, and the top right cell in the right array has a note.]
Four variations for determining the ratio between the diameter of the small circles and the distance between them. ¶Bottom left: grids with varying numbers of points or holes—5×5, 6×5, 6×7, and 8×8 (from top to bottom). From left to right, the same grids are shown, but with different spacing between the points. ¶Bottom right: same as left, but reduced in scale to 75%.
Above: a variation on the 5×5 grid: how does the letter look when extended vertically to 5×7? ¶Below: various options for the placement of the perforated letter-number combination and the word ‘NEDERLAND’, which was to be gold-foil stamped on the cover.
Top left: perforations in a 5×5 grid. ¶Bottom left: perforations in a 5×7 grid. ¶Top right: various layout options for the perforated alphanumeric code found in the passport (eg, ‘AB 12345’ or ‘AB 12 345’). ¶Bottom right: examples of several possibilities as developed by the State Printing Office.
Jurriaan Schrofer now wanted to develop a letterform from the ‘perforation alphabet’ that could be used as a typeface for the text. ¶Top left: the transition from the dot grid to a) an angular letterform and b) a letterform with rounded corners. ¶Middle and bottom: two versions of both alphabets, one with ’open’ letterforms, and one with ‘closed’ letterforms, so that the ‘a’, the ‘o’ and the ‘8’ have enclosed ‘islands’.
[If you look at the cover of Schrofer’s captions typescript above, you’ll see the title drawn by hand using the angular form of this script.]
At a compositor’s, a number of lines of text were photographically set from one of the alphabets (see also the panel on the wall).
Left: working mockups for a page of the passport on positive and negative photo material (Color-Key). ¶Right: To define the look of the layout, pages were designed with letters of five different heights, from 1 to 1.4 millimeters.
In the end, a font height of 1.5 millimeters was chosen. ¶Top: The version of the letterforms with the rounded corners. ¶Middle: version of the ‘angular’ alphabet.
Unlike in the initial design [the first proposal], printing a background pattern difficult to replicate was limited to the bottom third of the page. ¶The structure of this background was composed of a ‘dot alphabet’ and printed in two colors. The dots were printed in pairs[*], with their dimensions calculated so that even if the printing press failed to achieve perfect ‘registration’ (i.e., printing in the precisely intended position), the dots would still align; a tolerance of 0.02 millimeters was allowed. ¶The lettering started from a horizontal strip in the middle of the field containing the words ‘NEDERLAND PAYS BAS NETHERLANDS’. ¶The remaining letters of the alphabet were arranged from this strip vertically; for instance, above the letter ‘N’ appeared ‘MLKJ …’, while below it appeared ‘OPQRST …’.
[*Superimposed dots in fields of two colors.]
To assess the outcome as it would look when printed, a large working drawing on film (see panel on the wall) was reduced on photo material (Color-Key). ¶Below, a proof at actual size.
The printed background is composed of letters, but it also reveals the shapes of a square and a rhombus. The square is a fixed element: two per page. The rhombus, by contrast, shifts slightly in position relative to the squares, ensuring that no two pages are identical (see the sketch on page 19). ¶In addition to the changes in form brought about by this ‘traveling’ rhombus, there is also a continuous shift in color. Consequently, every vertical series of dots constitutes a unique combination that never recurs.
A number of calculations that preceded the series of shape transformations: ‘thinking with the pencil’.
The original idea was to create a computer program for the typesetting machine that would automatically ‘design’ the typesetting for the 22 pages. That would have taken quite a bit of time. To make two test pages for the model of the passport, Schrofer designed a cardboard slide on which the compositor could read exactly what he had to put per line (see also the panel on the wall).
Just as the background throughout the passport shifted in both form and color, the watermark was also envisioned as a changing sequence: for each page, R.D.E. Oxenaar[*] designed a symbol representing the concepts of ‘sun,’ ‘moon,’ and ‘weather,’ each in four variations. ¶An initial series of sketches for the so-called ‘shadow watermarks.’
[*‘Ootje’ Oxenaar was a well-known and prolific Dutch designer and illustrator who had joined the PTT in 1970. (He went on to direct its aesthetics advisory division from 1976–1990.) He’s perhaps best known for his stamp and especially banknote designs.]
[This board is likely missing one of Oxenaar’s sketches.]
The final proposal of 12 watermarks.
[Clearly missing 2 of Oxenaar’s drawings.]
The passport, as it was ultimately presented in 1973, came in three different color combinations. ¶So, why was the design never adopted? In the early 1970s, the European Community reached the consensus that it should strive toward a single European passport. The Netherlands supported this goal; consequently, a new Dutch passport was removed from the agenda.
My research on these proposals is very much work in progress. I’d like to get better images of the assembled boards, recreate the wall panels with the materials in the archive, and reproduce and annotate them all in greater detail.
Also: the designs for the type in the second proposal were the only scripts of Schrofer’s ever to have been realized as actual fonts, for phototypesetting when he was preparing the proposals in the early 70s and later as rudimentary digital fonts by his friend Kees Broos in the early or mid-1980s. I’ve created variable fonts from the designs myself with a contemporary font editor (RoboFont) and code (you can see them with other designs and applications in what I call Schrofer’s schema 05 ↗). But I’d like to know more about how Broos made his own versions back in the early years of desktop computing.
And I’m attempting to reverse-engineer and recreate Schrofer’s system for the security background pattern of letters and numerals in the second proposal, in order to realize his original idea for a program that would generate that pattern automatically.